Denon AVR-5805CI Manuel d'utilisateur Page 150

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 214
  • Table des matières
  • DEPANNAGE
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 149
150
Advanced Setup – Part 2
Setting the Direct Mode Setup
1
Press the CURSOR
DD
or
HH
button to select
“Direct Mode Setup” at the “Auto Setup /
Room EQ” menu, then press the
ENTER
button.
The “Direct Mode Setup” screen appears.
Set the ON/OFF setting of Room EQ, in the case of the
surround mode is in DIRECT or PURE DIRECT.
2
Press the CURSOR
FF
or
GG
button to select
“ON” or “OFF”.
3
Press the ENTER button to enter the setting.
The “Auto Setup / Room EQ” menu reappears.
Setting the MIC Input Select
1
Press the CURSOR
DD
or
HH
button to select
“Mic Input Select” at the “Auto Setup / Room
EQ” menu, then press the
ENTER button.
The “Mic Input Select” screen appears.
Set this to switch the Mic Input jack for use for Mic jack or
V.AUX L-channel input terminal.
2
Press the CURSOR
FF
or
GG
button to select
“Mic” or “V.AUX L”.
3
Press the ENTER button to enter the setting.
The “Auto Setup / Room EQ” menu reappears.
Required Microphone for DENON Auto-Setup Room EQ :
Product name Countryman B3
Required Microphone Amplifier Specification for DENON Auto-
Setup Room EQ
Gain : 29 dB
•Frequency Response : 10 ~ 30 kHz Full Flat
(Ex : Rane MS1b)
Micr
ophone Placement
Set the microphone using microphone stand, or other
method, at the prime listening position.
Point the top of the microphone toward the ceiling.
Adjust the height so that the top of microphone to matches
the height of your ear when sitting.
Micr
ophone Amplifier Gain Setting using Sound Level Meter
and RMS Volt Meter
First you will need to adjust the “ microphone amplifier gain”.
(1) Connect the all speakers and the video monitor (for the
on screen display) with the AVR-5805CI.
(2) Connect the microphone with the microphone amplifier.
(3) Turn on the AVR-5805CI and the “microphone amplifier”.
(4) Turn on the “Phantom Supply” on the microphone
amplifier.
(5) Set the Parameter “Test Tone” to “Manual” and “Test
Tone Start” to “Yes” at “Channel Level” ( page 143
~ 145).
(6) Once the test tone for Front Left (FL) speaker starts,
check the Sound Pressure Level at the Listening
Position with an SPL Meter. You do not have to check
any of the other channels.
(7) Adjust the “Main Volume” so that the Sound Pressure
Level measures 80 dB (C-weighted).
(8) Once the “Main Volume” as been set, connect the
output of microphone amplifier to the RMS Volt Meter.
(9) Adjust the “microphone amplifier’s gain” as the RMS
Volt Meter becomes about 120 [mV RMS].
(10) Once set, exit out of “System Setup” and turn off the
AVR-5805CI.
(11) Connect the output of the microphone amplifier to the
AVR-5805CI’s front panel “V.AUX” Left channel audio
input–located behind Trap Door.
(12) Change the setting to “V.AUX L” at “Mic Input Select”.
(13) Start “Auto Setup” ( page 20 ~ 26).
2 Specifications and Setup Procedure for Non-
DENON Microphone
Vue de la page 149
1 2 ... 145 146 147 148 149 150 151 152 153 154 155 ... 213 214

Commentaires sur ces manuels

Pas de commentaire