Denon AVR-1509 Manuel du propriétaire télécharger pdf (Page 20)

About the Auto Setup

The Audyssey MultEQ auto setup function detects the presence of

each speaker and automatically calculates the speaker size, channel

level, distance, and optimal crossover frequency setting. Audyssey

MultEQ corrects acoustical distortions within the listening area.

Before starting, connect and position all of your speakers.

Once started, MultEQ will play a series of test tones through each

speaker.

NOTE

Do not change the speaker connections or subwoofer volume after

“Step 1”.

If an error message appears during the measurements, check “Error

Messages”, take the advised action, then start the measurements

again (vpage 17).

The speaker connection and polarity are detected at the ﬁrst

measurement position (main listening position). The following

attributes are also determined at this time: “Speaker Size”, “Speaker

Distance”, “Channel Level”, “Crossover Frequency”.

q Press o while “Auto Set<Start” is displayed.

• While the measurements are being conducted “Measure:FL

<Ccl” (“FL” indicates the speaker being measured) is displayed.

• When the measurements are completed, the number of detected

speakers is displayed.

Example : For a 5.1 channel speaker conﬁguration

S p e a k e r : 3 / 2 / . 1

Step 1 : Speaker Detection

• If the result differs from the actual connection status or an error

message appears, use i to display “Retry<” and then press o to

repeat the measurement.

• If the result still differs from the actual connection status after

re-measurement or the error message still appears, it is possible

that the speakers are not connected properly. Turn the AVR-1509

off, check the speaker connections and repeat the measurement

process from the beginning.

Number of front speakers or

center speakers

a Auto Setup

The settings found at this stage are applied automatically.

GAuto setup ﬂowH

Step 1: Speaker Detection

Step 2: Measurement

Step 3: Calculation

Step 4: Check

Step 5: Store

Step 2 : Measurement

q Press i to select “2nd Start<”, then press o.

• The measurement of the 2nd position starts.

w Move the microphone to the 3rd position and press o.

• The measurement of the 3rd position starts.

e Perform w repeatedly.

• “Calculate<” is displayed when you have completed

measurements in 6 positions.

• If you want to stop after measuring just ﬁve or fewer positions,

use i to display “Calculate<”.

After completing a measurement position, move the microphone to

the next position.

Measure at 6 positions: the main listening position and 5 other

surrounding positions. Although it is allowable to measure less than 6

positions, it is recommended to measure 6 for best results.

NOTE

• Do not disconnect the setup microphone until the auto setup

procedure is completed.

• When using headphones, unplug the headphones before starting

the auto setup procedure.

NOTE

• Loud test sounds may be played during Audyssey MultEQ automatic

speaker setup. This is part of normal operation. If there is background

noise in room, these test signals will increase in volume.

• Do not stand between the speakers and setup microphone or allow

obstacles in the path while the measurements are being made. This

will cause inaccurate readings.

• Make the room as quiet as possible. Background noise can disrupt

the room measurements. Close windows, silence cell phones,

televisions, radios, air conditioners, ﬂuorescent lights, home

appliances, light dimmers, or other devices as measurements may

be affected by these sounds.

Cell phones should be placed away from all audio electronics during

the measurement process as Radio Frequency Interference (RFI)

may cause measurement disruptions (even if the cell phone is not in

use).

• Operating MASTER VOLUME during the measurements will cancel

the measurements.

• To cancel the measurements, press o while “Measure:FL <Ccl”

is displayed (“Ccl” stands for “Cancel”).

Step 3 : Calculation

The values obtained from the measurements are automatically

analyzed and the attributes for each of the speakers in the listening

area are determined.

q Press o while “Calculate” is displayed.

• “Calculating” is displayed and analysis begins.

• Analysis takes several minutes to complete.

• The time required for this analysis depends on the number of

speakers connected. The greater the number of speakers connected,

the longer analysis will take.

NOTE

Do not change the speaker connections or subwoofer volume,

or speaker locations after making measurements. If changes are

necessary, make the changes and use the Audyssey MultEQ auto

setup once again for an updated EQ solution.

Subwoofer

Yes: “.1”, No: “0”

Number of surround speakers

Auto Setup

Optimize settings for speakers in use.



Getting Started Connections Setup Playback Remote Control Information Troubleshooting

ENGLISH

Speciﬁcations

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 55 56

Commentaires sur ces manuels

Pas de commentaire

Denon AVR-1509 Manuel du propriétaire Page 20

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteur Denon AVR-1509